2018 March Latest Cisco 300-180 Exam Dumps with PDF and VCE Free Updated Today! Following are some new 300-180 Real Exam Questions:
1.|2018 Latest 300-180 Exam Dumps (PDF & VCE) 374Q&As Dowenload:
2.|2018 Latest 300-180 Exam Questions & Answers Download:
While attempting to boot a Cisco UCS server from SAN, you are unable to see the LUN. Which of these are causing the problem? (Choose three.)
A. VHBA template
B. RAID policy
D. LUN ID
F. disjoint fabrics
A Cisco UCS chassis has two ports on I/O Module 1 connected to Fabric Interconnect A, and two ports on I/O Module 2 connected to Fabric Interconnect B. The I/O modules are connected to ports 1 and 2 on their respective fabric interconnects, and end host mode is configured. After a link failure occurs on port 1 of I/O Module 1, what happens to the traffic that was pinned to that link?
A. The traffic fails until the link issue is resolved.
B. The traffic is repinned to I/O Module 2 link 1, which is connected to Fabric Interconnect B.
C. The traffic is repinned to the remaining link between I/O Module 1 and Fabric Interconnect A.
D. The traffic is repinned automatically to Fabric Interconnect B.
During a password recovery of a Cisco UCS system in a cluster configuration, what happens to blade traffic?
A. There is no interruption to traffic, as the fabrics go down one at a time.
B. Traffic stops flowing until the process is complete.
C. There is no interruption to traffic because both fabrics stay up the whole time.
D. Traffic will continue to flow, but at a limited rate until the process is complete.
For a KVM session to be successful, which two of these need to be done? (Choose two.)
A. The Cisco IMC IP address needs to be assigned on the Admin tab.
B. The Cisco IMC IP address needs to be in the same subnet as the management IP.
C. The Cisco IMC needs to be upgraded to the same version as the UCS Manager.
D. The server needs to be fully discovered.
As a Cisco UCS administrator, you have a large deployment of C-Series servers. You decide to integrate these into a Cisco UCS Manager environment to simplify management. Which two of these will you need to purchase? (Choose two.)
A. two fabric interconnects
B. a dedicated Cisco IMC
C. two fabric extenders
D. two I/O modules
Which three Cisco UCS server components can be upgraded via a host firmware package? (Choose three.)
B. Cisco UCS Manager
C. I/O module
D. Cisco IMC
E. fabric interconnect
G. board controller
Which three methods can be used to upgrade the Cisco IMC? (Choose three.)
A. host firmware package
B. blade firmware package
C. controller firmware package
D. management firmware package
E. directly on the blade, under the Installed Firmware tab
F. directly on the blade, under the Blade Firmware tab
G. directly on the blade, under Inventory > CIMC
Which command sequence in the Cisco UCS C-Series rack server CLI sends tech support data to a TFTP server?
A. ucs-c250 / # scope cimc
ucs-c250 /cimc # scope tech-support
ucs-c250 /cimc/tech-support # set path default.tar.gz
ucs-c250 /cimc/tech-support *# set tftp-ip 192.168.70.45
ucs-c250 /cimc/tech-support *# commit
B. ucs-c250 / # scope system
ucs-c250 /system # scope tech-support
ucs-c250 /system/tech-support # set path default.tar.gz
ucs-c250 /system/tech-support *# set tftp-ip 192.168.70.45
ucs-c250 /system/tech-support *# commit
C. ucs-c250 / # scope support
ucs-c250 /support # scope tech-support
ucs-c250 /support/tech-support # set path default.tar.gz
ucs-c250 /support/tech-support *# set tftp-ip 192.168.70.45
ucs-c250 /support/tech-support *# commit
D. ucs-c250 / # scope fault
ucs-c250 /fault # scope tech-support
ucs-c250 /fault/tech-support # set path default.tar.gz
ucs-c250 /fault/tech-support *# set tftp-ip 192.168.70.45
ucs-c250 /fault/tech-support *# commit
What is the recommended procedure to update Cisco UCS C-Series rack-mount server firmware?
A. Launch the Cisco UCS Firmware Update Utility from virtual media.
B. Launch the Cisco UCS Host Update Utility from virtual media.
C. Launch the Cisco UCS Server Update Utility from virtual media.
D. Launch the Cisco UCS CIMC Update Utility from virtual media.
You are installing Microsoft Windows Server 2008 R2 on a Cisco UCS C210 M2 server, and the installer does not see local storage on the LSI MegaRAID SAS 9260-4i controller that is installed.
Which statement explains the issue?
A. The driver is not included in the installer DVD. Press F6 to load the LSI RAID driver from CD or virtual media.
B. The virtual disk is not created and online.
C. The LSI 9260-4i is only supported by Red Hat Enterprise Linux and VMware vSphere 4.0 and later.
D. The installer DVD for Microsoft Windows Server 2008 R2 did not include the LSI driver until SP2.